Local Repair FinderAustin home repair guide

Breaker keeps tripping in Austin

Austin & Travis County · Reviewed November 2026 · Checked against 8 public sources

Breaker trouble, a burning smell or a panel upgrade?

Talk to a local electrician now. Free, no obligation.

Phone line opening soon
  • Free to call
  • No obligation
  • Local Austin companies
  • Ask for a written quote

Have this ready when you call

  • Your address
  • What lost power or keeps tripping
  • Anything warm, buzzing or smelling of burning

Unplug everything on the dead circuit, then reset the breaker once: fully Off, then On. If it holds, plug items back one at a time to find the overload. If it trips with nothing connected, or you notice heat, buzzing or a burning smell at the panel, stop and call an electrician. When the whole house is dark, report the outage to Austin Energy at 512-322-9100.

An open electrical breaker panel in a garage

Key facts

Reset rule
Once, with the circuit unplugged
Stop if
It trips empty, or the panel is hot, buzzing or smells burnt
House-wide outage
Austin Energy, 512-322-9100
Texas license
Electricians: TDLR
Upgrade permit
Residential Electrical Upgrade (City of Austin)
200-amp upgrade
$1,800–$4,500 (national, Fixr)

Safe to wait or not?

Can waitOne breaker that trips when a heater, hair dryer or microwave runs alongside other things, and holds once you spread the load. That is the breaker doing its job.
Can't waitA breaker that trips instantly with nothing plugged in, a hot or humming panel, scorch marks, a burning smell, or a main breaker that drops. Leave it off and call an electrician.

Six checks at the outlets and the panel door

  1. Is it just you? If every room is dark and the neighbors are too, no breaker is at fault. Austin Energy takes outage reports at 512-322-9100.
  2. Note what was running. Write down which breaker tripped and what had just been switched on. Space heaters, kettles, hair dryers, vacuums and window units are the usual suspects.
  3. Empty the circuit. Unplug every appliance and lamp in the rooms that went dead, and turn their wall switches off.
  4. Reset one time. Open the panel's hinged door and find the handle sitting out of line. Press it firmly to Off, then to On; if it snaps back immediately, leave it and skip to the next section.
  5. Add things back singly. Plug in one item, wait a minute, then the next. The device that trips the breaker, or the combination that does, is your answer; move a heavy load to an outlet on another circuit.
  6. Press the outlet buttons. Kitchen, bathroom, garage and outdoor outlets often have Test and Reset buttons. A dead outlet with a live breaker may only need Reset pushed in.

When the checks don't fix it

Stop resetting and call an electrician when:

  • The breaker won't hold with the circuit completely unplugged.
  • The handle or the panel cover feels warm.
  • You hear crackling or humming, or smell hot plastic.
  • An outlet or switch plate is discoloured.
  • The same breaker trips every few days under ordinary use.
  • The trip follows a roof leak or other water getting into a wall or ceiling.

Repeated resets force current through a fault. The panel's inner cover stays on; what lies behind it is live even with breakers off.

Want a price for your home? Call a local electrician for a written quote.

Phone line opening soon

If the breaker belongs to the AC

An air conditioner's breaker gets its hardest test in summer; Camp Mabry's normal July high is 96.6 °F. Reset it once and no more. A second trip sends you to the AC not cooling page and an AC technician.

Who may work on it

Texas electricians are licensed through the Texas Department of Licensing and Regulation. Enter the electrician's or company's name in the TDLR's license search before the appointment.

The City of Austin's Homestead Permit allows some owners to do electrical work in the home they live in, but it rules out the main electric service. Diagnosing a breaker that trips under fault is not a sensible first project in any case.

Permits: a like-for-like breaker versus an upgrade

Austin's exempt work list includes replacement of branch circuit overcurrent devices of the required capacity in the same location. In plain terms, an electrician swapping a worn breaker for a matching one is on the exempt list.

Larger work is different. The City lists a residential Electrical Upgrade permit for upgrade work that doesn't need formal plan review, and a registered contractor applies for it.

What it may cost

This guide has no verified Austin price for tracing a fault or replacing a breaker. If the electrician finds the panel itself is too small, Fixr's national figure for moving to 200-amp service is $1,800 to $4,500; the panel upgrade page covers that job.

What a repair usually costs

National ranges from cost publishers, not Austin quotes. The fault decides the price, so ask for it in writing before work starts.

JobNational rangeSource
Replacing a circuit breaker$100 to $260HomeGuide

When you call: 4 questions to ask

  1. What's your TDLR electrical license number?
  2. Will you pull the City's electrical upgrade permit?
  3. Will the new panel handle a heat pump or a car charger later?
  4. Is the trip charge taken off the job?

A fair written quote shows the panel, labor, the permit and inspection, with extra wiring listed separately. Check any contractor's license on the TDLR license search before work starts.

What happens when you call

  1. You're connectedStraight to a local electrician that serves your area and takes calls like yours.
  2. You get a priceDescribe the problem, ask for a written quote and their license number. No obligation.

Common questions

Why does my breaker keep tripping?

Most often too many high-draw devices share one circuit. Less often a faulty appliance, a damaged cord, moisture or a wiring fault is to blame, and those need an electrician.

How many times can I reset a tripped breaker?

Once, after unplugging what's on the circuit. If it trips again with little or nothing connected, leave it off.

Is a tripping breaker dangerous?

The trip itself is protection working. The danger signs are heat, buzzing, a burning smell, scorch marks, or a breaker that refuses to stay on with the circuit empty.

Does replacing a breaker need a permit in Austin?

The City's exempt list includes replacing a branch circuit overcurrent device of the required capacity in the same location. Upgrades fall under the residential Electrical Upgrade permit, which a registered contractor obtains.

Related guides

Sources

  1. Austin Energy: Report outages
  2. National Weather Service Austin/San Antonio: July climate sheet, Camp Mabry (Normals 1991-2020)
  3. TDLR: Electricians
  4. TDLR: Active License Search
  5. City of Austin Development Services: Homestead (homeowner's) permit
  6. City of Austin Development Services: Work exempt from building permits
  7. City of Austin Development Services: Types of permits
  8. Fixr: Electrical panel upgrade cost (national)

Costs are typical ranges. Your quote depends on your home. Rules and rebates change; check the original source before you rely on a figure. Something wrong? Tell us via the contact on the Impressum page.