Local Repair FinderFort Worth home repair guide

Breaker keeps tripping in Fort Worth

Fort Worth & Tarrant County · Reviewed November 2026 · Checked against 7 public sources

Breaker trouble, a burning smell or a panel upgrade?

Talk to a local electrician now. Free, no obligation.

Phone line opening soon
  • Free to call
  • No obligation
  • Local Fort Worth companies
  • Ask for a written quote

Have this ready when you call

  • Your address
  • What lost power or keeps tripping
  • Anything warm, buzzing or smelling of burning

A breaker that trips is doing its job. Unplug everything on that circuit, reset it one time, then bring devices back one by one to see whether a single appliance or sheer load is the cause. Heat, buzzing, a burning smell, or a trip with nothing connected all mean stop and call an electrician. In Texas, electricians are licensed by TDLR, and Fort Worth requires a permit for electrical repairs.

An open electrical breaker panel in a garage

Key facts

First five minutes
Smell and touch check, unplug the circuit, one reset
Next hour
Add loads back singly; test outlet reset buttons
Outage or damaged outdoor lines
Oncor Electric Delivery, 888.313.4747
Permit
Electrical permit for changing, moving or repairing electrical equipment, including electrical services
License to ask for
Texas electrician license (TDLR)
200 amp service upgrade
$1,800–$4,500 to upgrade to 200-amp service (Fixr cost table)

First five minutes

  1. Use your nose and the back of your hand. A hot breaker, a warm panel door, a burning or fishy smell, crackling or buzzing: any of these ends the homeowner part. Leave the breaker off and call an electrician. Smoke or flames are for 911.
  2. Identify the circuit. Read the panel label or note which rooms went dark.
  3. Unplug it all. Every lamp, charger, appliance and power strip on that circuit, and switch its lights off.
  4. Reset one time. Push the handle firmly to Off, then to On. If it snaps back with nothing connected, stop there.

Next hour

  1. Reconnect one device at a time. Wait a minute or two between each. If the trip follows one appliance, that appliance is the suspect. Leave it unplugged.
  2. Add up the big draws. Space heaters, hair dryers, microwaves, toasters, window units and vacuums each pull a lot. Two on one circuit is a classic overload. Move one to an outlet in another room.
  3. Press Reset on button outlets. Kitchens, bathrooms, garages and outdoor outlets often have Test and Reset buttons. A dead outlet with the breaker on may just need Reset. If it pops again, something on that line is leaking current, often from moisture.
  4. Notice the timing. A trip when the AC or another large appliance starts, or only during storms, is useful detail for an electrician.
  5. Keep a short log. Which breaker, what was running, what time. Patterns shorten the visit.

Want a price for your home? Call a local electrician for a written quote.

Phone line opening soon

Do and don't

DoDon't
Reset a tripped breaker once, after unplugging the circuitHold, tape or wedge a breaker in the On position
Shift heavy appliances to different circuitsSwap in a larger breaker to stop the tripping
Leave a suspect appliance unpluggedTake the cover off the panel
Use the buttons on the face of an outletRun extension cords as a lasting fix

Stop and call a pro when

  • The breaker trips at once with nothing plugged in.
  • It trips again after you have spread the load around.
  • The breaker, panel, an outlet or a switch plate feels hot or shows scorch marks.
  • Lights dim or flicker across several rooms.
  • The main breaker trips, or half the house loses power.
  • The panel has got wet.

Before a repair starts

Summer load

With a normal July high of 95.6 °F at the area's official climate station, air conditioning runs for long stretches in summer. If trips cluster on hot afternoons, say so when you call; it helps separate a household overload from a failing AC component, which is covered on the AC not cooling page.

If it is not your wiring

Power lost to the whole house goes to Oncor Electric Delivery, which delivers electricity in Fort Worth: 888.313.4747. For a downed or damaged line, stay away, leave the area and call 911; the 911 operator contacts Oncor.

Permit

The City of Fort Worth's residential permit page states that changing, moving or repairing electrical equipment, including electrical services, requires an electrical permit. Electrical service work needs a permit, in other words, and the City's homestead affidavit adds that homeowners may not work on the service; that work must be permitted and done by a Master Electrician.

License

The Texas Department of Licensing and Regulation regulates electrician licenses for individuals and businesses. Enter the name or number in the TDLR's Active License Search, which lists active licenses only.

Price

This guide has no Fort Worth figure for replacing a breaker or tracing a fault; the table below gives a national range for replacing one. If the electrician finds the service is too small for the house, Fixr's cost table puts upgrading to 200-amp service at $1,800 to $4,500. It is a countrywide figure; the panel upgrade cost page has the detail.

What a repair usually costs

National ranges from cost publishers, not Fort Worth quotes. The fault decides the price, so ask for it in writing before work starts.

JobNational rangeSource
Replacing a circuit breaker$100 to $260HomeGuide

When you call: 4 questions to ask

  1. Under which TDLR license number will this work be done?
  2. Who applies for the Fort Worth electrical permit, and who meets the inspector?
  3. Is there spare capacity for a future heat pump or car charger?
  4. Do you charge to come out, and does that charge come off the job?

A fair written quote shows parts, labor, the permit and inspection, and any extra wiring repairs listed as separate lines. Check any contractor's license on the TDLR license search before work starts.

What happens when you call

  1. You're connectedStraight to a local electrician that serves your area and takes calls like yours.
  2. You get a priceDescribe the problem, ask for a written quote and their license number. No obligation.

Common questions

Why does my breaker keep tripping?

The three usual reasons are too much load on one circuit, a faulty appliance, or a wiring fault. Unplugging everything and adding devices back one at a time tells you which of the first two it might be.

How many times can I reset a tripped breaker?

Once. If it trips again, find out why before touching it. Repeated resets against a real fault build heat in the wiring.

Is a tripping breaker dangerous?

The trip itself is protection. The danger signs are heat, a burning smell, buzzing, scorch marks or a breaker that won't stay on with nothing connected.

Do I need a permit for electrical repairs in Fort Worth?

The City of Fort Worth says changing, moving or repairing electrical equipment, including electrical services, requires an electrical permit.

Related guides

Sources

  1. National Weather Service Fort Worth office: normals, means and extremes
  2. City of Fort Worth Development Services: Residential permit information
  3. Texas Department of Licensing and Regulation: Electricians
  4. TDLR's Active License Search
  5. Oncor Electric Delivery: Storm center update on Fort Worth restoration
  6. Oncor Electric Delivery: Outage FAQs
  7. Fixr: Electrical panel upgrade cost (national)

Costs are typical ranges. Your quote depends on your home. Rules and rebates change; check the original source before you rely on a figure. Something wrong? Tell us via the contact on the Impressum page.