Cut power to an electric water heater at its breaker, then close the cold-water valve on the pipe entering the top of the tank. That stops the tank refilling. If water keeps coming, shut the home's main valve. Smell gas? Leave, then call Spire on 800-752-7504 and 911 from a safe place. A tank leaking from its base usually means replacement: $1,000 to $2,700 for a gas tank on national figures.
Key facts
- Step one
- Electric: breaker off. Gas: leave the controls alone
- Step two
- Close the cold-water valve above the tank
- Gas smell
- Leave, then Spire 800-752-7504 and 911
- Gas tank heater, installed
- $1,000–$2,700 (national, Fixr)
- Permit
- 50-gallon like-for-like: generally none; fuel change: required (Metro Codes)
- Rebate
- $900 off a qualifying heat pump water heater (TVA EnergyRight)
Short version: take away the power, take away the water supply, contain the puddle, and let a plumber decide between a fitting and a new tank.
What you can check
- Power. For an electric unit, switch off the water heater breaker, standing on a dry floor. For a gas unit, don't handle the gas control or reach near the burner; closing the water in the next step is enough for now.
- Cold-water valve. Follow the pipe that feeds the top of the tank to its valve. A lever handle turns a quarter turn until it sits across the pipe; a round handle turns clockwise until it stops. If the valve is seized or drips, close the main valve for the house.
Power off and water valve closed? Good moment to phone a local plumber. Keep going with the list while you wait.
Phone line opening soonHave this ready when you call
- Your address
- Where the water is and whether the main is off
- When it started
- Find the wet spot. Look, without loosening anything. Water at the pipe connections on top, water from the pipe that runs down the side from the relief valve, and water seeping from under the jacket are three different problems, and the plumber will ask which.
- Contain it. Put a bucket or pan under the drip, lay towels as a dam, and lift cardboard boxes, paint cans and anything electrical off the floor.
- Take pictures. Photograph the tank's data label, the leak and any wet flooring or drywall. The label tells the plumber the size and fuel; the rest is for your insurer.
- Check next door. If the heater sits in a closet or on an upper floor, look at the room below and the wall behind for staining.

What not to touch
Stay away from the gas valve, the pilot and the burner compartment. Don't cap, plug or tie down the relief valve or its discharge pipe; it exists to release pressure. Don't remove the electric element covers. Draining a tank through its bottom valve is a job to leave for the plumber, since old drain valves often won't close again.
Stop and call a pro when:
- water is coming from the tank body or its base;
- the relief valve pipe is running or spitting hot water;
- the shutoff valve won't close;
- you see rust streaks, scorch marks or soot on the unit;
- water has reached a wall, a ceiling below or finished flooring.
The Nashville part
Spire. For a gas smell at any point, leave first, then call Spire at 800-752-7504 and 911 from a safe place.
Metro Water Services. Metro Water lists 615-862-4600, option 3, for 24/7 emergency service or to report a leak. It says the customer owns the line from the meter box to the house, so a leaking water heater inside is a job for your plumber, not Metro.
Metro Codes. A Metro Codes repair guideline says replacing a residential 50-gallon water heater generally does not require a permit, and that changing the fuel type, gas to electric for example, does. It is silent on bigger tanks, so for one of those ask Metro Codes and Building Safety on 615-862-6500.
License. Tennessee issues a Limited Licensed Plumber (LLP) license for plumbing projects that total less than $25,000 with materials and labor, and a contractor license (CMC or CMC-A) from $25,000. The state adds that the LLP isn't accepted in places with their own licensing and inspections, and Metro Nashville runs a plumbing exam of its own. So ask for the plumber's Metro license; state licenses can be looked up on Tennessee's license search.
Cost. Fixr's national range for a tank-style gas water heater, installed, is $1,000 to $2,700. That isn't a Nashville price, and the guide has no figure at all for repairing a valve or fitting. More detail is on the water heater cost page.
Rebate. TVA EnergyRight lists $900 off a qualifying heat pump water heater, an electric type. Piedmont (now Spire) says no gas equipment rebates are available in its Tennessee service territory.
What a repair usually costs
National ranges from cost publishers, not Nashville quotes. The fault decides the price, so ask for it in writing before work starts.
| Job | National range | Source |
|---|---|---|
| Water heater repair | $150 to $750 | Fixr, updated Aug 2025 |
When you call: 4 questions to ask
- Is this a like-for-like swap, or does the fuel type change and need a permit?
- Would a heat pump water heater get the $900 TVA EnergyRight rebate?
- Which plumbing license covers a job this size?
- Is the service-call fee credited on the repair?
A fair written quote shows the heater, labor, any permit, haul-away of the old tank and the written warranty. Check any contractor's license on the Tennessee license search before work starts.
What happens when you call
- You're connectedStraight to a local plumber that serves your area and takes calls like yours.
- You get a priceDescribe the problem, ask for a written quote and their license number. No obligation.
Want a price for your home? Call a local plumber for a written quote.
Phone line opening soonCommon questions
Is a leaking water heater an emergency?
It's urgent rather than dangerous in most cases. Shut off power and the cold-water valve and the leak slows to what's left in the tank. Treat a gas smell or a spraying relief valve as an emergency.
Can a leaking water heater be repaired or does it need replacing?
Leaks at the top fittings or valves can often be repaired. Water coming from the tank itself generally means the tank has failed and the unit is replaced.
Do I need a permit to replace a water heater in Nashville?
Metro Codes guidance says a residential 50-gallon replacement generally does not need a permit, but changing fuel type does. Ask Metro Codes about larger tanks.
How much is a new water heater in Nashville?
The guide has no local price. Fixr's national range for an installed gas tank water heater is $1,000 to $2,700.
Related guides
Sources
- Spire: Contact us (Tennessee emergency line and gas leak steps)
- Metro Water Services: Customer information and emergency line
- Metro Codes: Repair guidelines for water heating systems
- Metro Codes and Building Safety: Contact information
- Tennessee Department of Commerce and Insurance: Who needs a Limited Licensed Plumber (LLP) license
- Tennessee Department of Commerce and Insurance: License search
- Fixr: Gas water heater installation cost (national)
- TVA EnergyRight: Water heating rebates
- Piedmont Natural Gas: Energy efficiency programs
Costs are typical ranges. Your quote depends on your home. Rules and rebates change; check the original source before you rely on a figure. Something wrong? Tell us via the contact on the Impressum page.