Local Repair FinderColorado Springs home repair guide

High-altitude furnace sizing in Colorado Springs

Colorado Springs & El Paso County · Reviewed November 2026 · Checked against 2 public sources

No heat, or a furnace on its last legs?

Talk to a local heating & cooling pro now. Free, no obligation.

Phone line opening soon
  • Free to call
  • No obligation
  • Local Colorado Springs companies
  • Ask for a written quote

Have this ready when you call

  • Your address
  • What the system is doing (no heat, no cooling, a noise, a leak)
  • Roughly how old the unit is

Gas furnaces are rated at sea level. Many furnaces must be derated, commonly 4% per 1,000 feet of elevation when installed above 2,000 feet (ACHR News); some models need only 2%. The model's manual sets the rule, and orifice changes depend on the model and elevation. At about 6,000 feet, a furnace labeled 100,000 BTU may be set to roughly 76,000–88,000 BTU input, depending on the model's instructions. Your installer should size from a load calculation and set it up for altitude.

Key facts

Common derate
4% of input per 1,000 ft (many manuals: above 2,000 ft)
Some condensing models
2% per 1,000 ft (manufacturer-specific)
Colorado Springs elevation
About 6,000 ft
Typical result for a 100,000 BTU nameplate
Roughly 76,000–88,000 BTU input, by model
Hardware
High-altitude orifices; some models also need a pressure switch change

Why altitude matters

Air at 6,000 feet is thinner, so each cubic foot carries less oxygen. A burner set up for sea level would get too much gas for the available air: incomplete combustion, sooting, and more carbon monoxide. Manufacturers fix this by reducing the gas input at altitude, usually with smaller burner orifices, and on some models a different pressure switch.

The trade press (ACHR News) quotes a manufacturer saying most of its furnaces need a 4% derate per 1,000 feet of elevation when installed above 2,000 feet, and some models only 2%; orifice and pressure-switch changes depend on the model and elevation. Always follow the specific model's installation manual.

What that does to a furnace's real size

Derate rule (model-specific)Reduction at 6,000 ft100,000 BTU nameplate becomes
4% per 1,000 ft of elevation24%≈ 76,000 BTU input
2% per 1,000 ft of elevation12%≈ 88,000 BTU input

Output (the heat delivered to your house) is the input times the furnace's efficiency. A 95% furnace at 76,000 BTU input delivers about 72,000 BTU.

Want a price for your home? Call a local heating & cooling pro for a written quote.

Phone line opening soon

Don't just match the old label

Many older Colorado Springs furnaces were oversized. Replacing them with the same nameplate number can still be too big, which causes short cycling, temperature swings and more wear. Ask for a Manual J load calculation, then choose a furnace whose derated output covers that load.

Questions to ask your installer

  • What derate does this model's manual require at my elevation, and what parts (orifices, pressure switch) does that involve?
  • What will the input and output be after derating?
  • Will you check gas pressure and combustion after installation?
  • Is the PPRBD mechanical permit and inspection included?

Water heaters and other gas appliances

The same principle applies to gas water heaters, boilers, fireplaces and ranges. Manufacturers publish high-altitude instructions; a licensed installer should follow them.

When you call: 4 questions to ask

  1. Is the diagnostic or trip fee credited toward the repair?
  2. Will you size a new system with a load calculation and set it up for our altitude?
  3. Is the PPRBD mechanical permit included, and what's your PPRBD license number?
  4. Does this model qualify for the Colorado Springs Utilities rebate, and who files it?

A fair written quote shows model numbers and efficiency, altitude setup, the permit and inspection, removal of the old unit, and parts and labor warranty. Check any contractor's license on pprbd.org before work starts.

What happens when you call

  1. You're connectedStraight to a local heating & cooling pro that serves your area and takes calls like yours.
  2. You get a priceDescribe the problem, ask for a written quote and their license number. No obligation.

Common questions

Do I need a special furnace for Colorado Springs?

Usually not a special model, but it must be set up for altitude per the manufacturer's manual, typically with high-altitude orifices and sometimes a different pressure switch.

How much capacity does a furnace lose at 6,000 feet?

Depending on the model's rule, about 12% to 24% of its sea-level input. A 100,000 BTU nameplate furnace may be set to roughly 76,000–88,000 BTU input.

Is the derate my installer's job?

Yes. Altitude setup is part of a correct installation and should be included in the quote and checked at the PPRBD inspection.

Related guides

Sources

  1. ACHR News: Furnaces must be modified for high-altitude applications
  2. Pikes Peak Regional Building Department: Homeowner permits: what needs a permit, homeowner rules, licensed contractors

Costs are typical ranges. Your quote depends on your home. Rules and rebates change; check the original source before you rely on a figure. Something wrong? Tell us via the contact on the Impressum page.