Local Repair FinderFort Worth home repair guide

Water heater leaking in Fort Worth

Fort Worth & Tarrant County · Reviewed November 2026 · Checked against 7 public sources

Close the cold-water valve on the pipe feeding the heater; that cuts off the tank's refill. Keep feet and hands out of water near wiring, and on an electric unit switch its breaker off. Then work out whether the drip starts at a fitting on top or from the tank body. A tank that leaks from the bottom is finished. Fixr's national range for a gas tank replacement is $1,000 to $2,700.

Key facts

First five minutes
Cold supply valve closed; electric unit's breaker off
Next hour
Trace the source, contain water, photograph
Gas smell
Leave, then 911 and Atmos Energy, 866.322.8667
Permit for the fix
Plumbing permit, water heaters included
License to ask for
Texas State Board of Plumbing Examiners license
Gas tank replacement
$1,000–$2,700 installed (national range, Fixr)
Atmos Energy rebate
$100 to $300 on qualifying natural gas models

First five minutes

  1. Shut the cold inlet valve. Above the heater, one pipe brings cold water in and has a handle or lever on it. Turn the handle clockwise until it stops, or swing the lever across the pipe. If it is seized, close the main valve for the house instead.
  2. Deal with the power side. For an electric heater, switch its breaker off. For a gas heater, leave the controls and the gas line alone; if you smell gas, leave the area, then from a safe distance call 911 and Atmos Energy at 866.322.8667.
  3. Cold supply closed and water still appearing under the tank? Call a local plumber, then finish the list.

    Phone line opening soon

    Have this ready when you call

    • Your address
    • Where the water is and whether the main is off
    • When it started
  4. Mind the floor. Water around a heater can be hot, and it may be touching cords or an outlet. Step around it, not through it.
  5. Start catching. A baking tray, a bucket, towels rolled into a dam. Move boxes and anything stored on the floor nearby.
Water pooling in a drain pan around the base of a water heater

Next hour

  1. Find the highest wet point. Dry the tank with a rag and watch. Moisture at the pipe connections on top is often a fitting. Water running from the pipe attached to the relief valve on the side is a pressure or valve issue. Water seeping from the seam at the base means the tank itself has failed.
  2. Check what the water reached. Drywall, baseboards, a closet floor or the ceiling of the room below if the heater sits upstairs or in the attic.
  3. Take pictures. The leak point, the data label on the tank, and every wet surface, with the time.
  4. Open a hot tap briefly. With the inlet closed, a hot faucet that slows to a trickle confirms the valve is holding.

Do and don't

DoDon't
Close the cold supply at the heater or at the mainCap, plug or tie off the relief valve pipe
Switch off the breaker on an electric modelTurn knobs on the gas control or try to relight anything
Keep the area clear so a plumber can reach the tankOpen the heater's access covers
Dry what got wet as soon as the flow stopsLeave a slow drip for another week

Stop and call a pro when

  • Water comes from the bottom of the tank or from under the jacket.
  • The relief valve pipe keeps discharging.
  • The inlet valve will not close or drips at its stem.
  • There is rust-coloured water, popping or rumbling from the tank.
  • Any of it happened on a gas heater and you are unsure of its state.

Before a repair starts

Permit

The City's residential permit page names water heaters in its plumbing permit rule: installing, changing, moving or repairing plumbing all require one. Confirm the permit is part of the written price.

License

Plumbers in Texas answer to the Texas State Board of Plumbing Examiners (TSBPE). Take the license number from the estimate and run it through the board's Public License Search.

Price and rebate

For a tank-style natural gas water heater, Fixr's national installed range is $1,000 to $2,700. It is not a Fort Worth number, and this guide has none for a valve or fitting repair. Atmos Energy's Mid-Tex program (July 1, 2026 to June 30, 2027) pays $100, $150 or $200 on natural gas storage tanks depending on efficiency rating, and $200 or $300 on gas tankless units. The tiers are laid out on the water heater cost page.

Insurance

The Texas Department of Insurance draws the line at how the water escaped: a sudden and accidental release is covered under a home policy, a continuous leak is not. A tank that let go this morning sits on one side of that line; months of seepage sit on the other. If floors or walls are wet, go to water damage: what to do first.

What a repair usually costs

National ranges from cost publishers, not Fort Worth quotes. The fault decides the price, so ask for it in writing before work starts.

JobNational rangeSource
Water heater repair$150 to $750Fixr, updated Aug 2025

When you call: 4 questions to ask

  1. Is there a call-out charge, and is it folded into the job if I go ahead?
  2. Will you give me one fixed price before any work starts?
  3. Does your price cover the Fort Worth plumbing permit?
  4. Which Texas State Board of Plumbing Examiners license do you hold, and under what number?

A fair written quote shows materials, labor, the permit, disposal of the old unit, and written warranty terms. Check any contractor's license on the TDLR license search before work starts.

What happens when you call

  1. You're connectedStraight to a local plumber that serves your area and takes calls like yours.
  2. You get a priceDescribe the problem, ask for a written quote and their license number. No obligation.

Want a price for your home? Call a local plumber for a written quote.

Phone line opening soon

Common questions

What do I do first if my water heater is leaking?

Close the cold-water supply valve above the heater so the tank stops refilling. On an electric unit, switch off its breaker. Then contain the water and look for where it starts.

Can a leaking water heater be repaired?

A loose fitting or a faulty relief valve can often be repaired by a plumber. A tank leaking from its base or seams cannot, and has to be replaced.

Do I need a permit to replace a water heater in Fort Worth?

Yes. The City of Fort Worth says changing, installing, moving or repairing plumbing, including water heaters, requires a plumbing permit.

How much does a new water heater cost?

Fixr's national range for a gas tank-style heater is $1,000 to $2,700 installed. There is no Fort Worth-specific figure in this guide.

Related guides

Sources

  1. City of Fort Worth Development Services: Residential permit information
  2. Texas State Board of Plumbing Examiners
  3. TSBPE Public License Search
  4. Atmos Energy: Gas safety
  5. Fixr: Gas water heater cost (national)
  6. Atmos Energy: Mid-Tex appliance rebate program
  7. Texas Department of Insurance: Homeowners insurance guide

Costs are typical ranges. Your quote depends on your home. Rules and rebates change; check the original source before you rely on a figure. Something wrong? Tell us via the contact on the Impressum page.